PLUMBING 101: TIPS FOR BATHTUB INSTALLATION

Plumbing 101: Tips for Bathtub Installation

Plumbing 101: Tips for Bathtub Installation

Blog Article

Call Today

The writer is making several good points about How to Install a Bathtub Yourself overall in this post below.


How to Install a Bathtub
Setting up a bathtub isn't specifically rocket science, but it does call for strong plumbing, woodworking, and occasionally, tiling abilities. Changing an old bath tub with a new one is likewise a moderately difficult job. If the old bathtub is readily easily accessible, the job can move speedily; if you have to open a wall to remove the old tub and position the new bathtub, the job is a lot harder. In either instance, the project is within a residence handyman's skills, although you will certainly require a helper to move out the old tub as well as set in the brand-new one. See to it you have certified on your own for the task and fit attempting it. As opposed to hiring a contractor to take over a halfway-completed task, it is far better to consider using one prior to you begin. Chances are you may need a specialist plumber to make tube links.
This post will certainly help you mount a new bath tub in your restroom if you have actually currently bought a brand-new bathtub and don't require to change the plan of your previous water pipelines.
Your tools and product checklist should consist of the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Removing Old Touches


    If you require to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is separate the water supply. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of removing the existing taps can be rather bothersome as a result of the restricted gain access to that is commonly the case.
    Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been eliminated, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this process. Once the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
    Before proceeding to fit the new faucets, contrast the pipeline links on the old taps to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.

    Fitting New Taps


    If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipelines.
    If you require to fit a monobloc, then you will certainly need reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
    Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in area in between the tap and also the sink. Secure the faucet in place with the producer given backnut. As soon as the tap is securely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous type ought to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

    Mounting the Bath tub


    Utilizing the two wooden boards under its feet, put the bathtub in the called for placement. The wood boards are helpful in evenly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
    The next objective is to make certain that the bathtub is leveled all round. This can be achieved by examining the spirit level and adjusting the feet on the bathtub till the level checks out degree.
    To set up taps, fit all-time low of the outermost adaptable tap port to the suitable supply pipe by making a compression join; then do the very same for the various other faucet.
    Activate the water and examine all joints as well as brand-new pipework for leaks and tighten them if necessary. Fill up the bathtub and also examine the overflow electrical outlet and the regular outlet for leakages.
    Finally, take care of the bath paneling as explained in the manufacturer's instruction manual. Tiling and sealing around the tub should wait until the bath tub has been utilized a minimum of once as this will certainly resolve it right into its last position.

    Preparing for the Setup


    Firstly, the supporting frame provided with the bath needs to be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to make sure that if the tap comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps system to stop pressure on the bathtub.
    Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the supplied washing machines.
    Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its last placement.

    Tiling Around the Bath tub


    In the location where the bath meets the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to split a rigid seal, causing the water to permeate the wall surface in between the bath and also the tiling, bring about issues with moisture as well as feasible leaks to the ceiling listed below.
    You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes as well as cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill the bath tub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can split relatively early if you do not take into consideration this activity prior to sealing.
    Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise easily readily available on the market. It is recommended to fit the ceramic tiles making use of waterproof or waterproof sticky as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    I was shown that write-up on Tools You Need to Install a New Bathtub from an acquaintance on our other domain. Loved our article? Please share it. Let another person discover it. I praise you for your time. Please come visit our blog back soon.


    Check It Out

    Report this page